2026
Version: 10.5.2
Your 3th eye in the sky.
3EYE is a head-up display altimeter and variometer for skydivers, projecting real-time altitude and vertical speed data directly onto your helmet visor. Alternatively, it can be configured as a standard skydiver altimeter. The device offers four customizable views to suit different flying styles:
Skydive altimeter (AV) – Displays altitude.
Dynamic variometer (DY) – Displays vertical speed changes optimized for the unique flight dynamics of wingsuit flying.
Speed dive variometer (SP) – Measures rapid vertical descents.
Standard variometer (V) – Measures gradual altitude changes.
To complement these views in measuring mode, 3EYE also operates in four additional modes that enable simulation, configuration, logging, and data management. This ensures flexibility and ease of use for every pilot.
| Specification | Value |
|---|---|
| Dimensions | 52 × 26 × 16 mm |
| Mass | 38 g |
| Digit height | 12 mm |
| Display | RGB LED 2 digits |
| Pilot views | Altimeter, Dynamic Vario, Speed Dive Vario, Standard Vario |
| Units | m / ft · m/s / ft/s · km/h / mph |
| Max altitude | 9000 m |
| Absolute/relative accuracy | 4 m / 1 m |
| Display orientation | Head-up (mirrored) / head-down |
| Altitude warnings | Configurable color zones + visual warnings |
| Display intensity | Adjustable + Night Mode |
| Event logging | Automatic |
| Log book | Up to 500 events / unlimited local archive with Link3EYE |
| Connection | Bluetooth Low Energy |
| Companion app | Link3EYE — Android & Chrome |
| Charging | USB-C |
| Battery | 830 mAh rechargeable |
| Working time | Up to 40 jumps in Altimeter mode |
| Controls | One button + Link3EYE configuration |
| Enclosure / protection | Aluminum / tempered display glass |
One button is used to perform 2 basic functions:
A short press (less than 1 second): cycle through menu items or views,
A long press (2s to 3s seconds): confirm a selection or enter a mode.
To turn on:
Hold the button until display becomes live (2s). If successful, 3EYE will show the battery status, metric or imperial configuration (m of f).
Press the button briefly to switch between modes.
Hold button 2s (unit LED intensity increase) to step into the mode.
⚠️WARNING The device may only be turned on at ground level, and the pressure must remain stable for at least 5 seconds (with no vertical event in progress).
⚠️WARNING If you do not enter any mode within 30 seconds, the 3EYE will automatically shut down.
NOTICE If the battery level is less then 20%, the device will not start.
To turn off:
Press the button briefly until exit code (EX) appears.
Hold the button for 2s (unit LED intensity increase).
Release the button immediately.
If you exit from any mode (AltVar, Demo, Config or Delete) you must repeat the sequence or wait 30s until device automatically shutdown.
⚠️WARNING 3EYE automatically stops after 14 hours.
To change views, short press the button briefly to cycle through menu.
3EYE uses codes to represent modes, views and configuration, as the display shows only two characters.
| Mode | Code | Description |
|---|---|---|
| AltVar | AV | Main measuring mode |
| Demo | DE | Simulation mode |
| Configuration | CF | Adjust settings |
| Delete | DL | Delete all logs and set factory setting |
| Exit | EX | Exist from the mode of stop 3EYE |
| View | Code | Units |
|---|---|---|
| Skydive altimeter | AL | [m] or [ft] |
| Dynamic variometer | DY | [m/s] or [ft/s] |
| Speed dive variometer | SP | [km/h] or [mph] |
| Standard variometer | V | [m/s] or [ft/s] |
| Unit | Code | Description |
|---|---|---|
| Meter | M | [m] |
| Feet | F | [ft] |
| Meter per second | M.S | [m/s] |
| Feet per second | F.S | [ft/s] |
| Kilometer per hour | KH | [km/h] |
| Mile per hour | ML | [mph] |
| Configuration | Code | Description |
|---|---|---|
| Meter | M | SI units (m, m/s, km/h) |
| Feet | F | Imperial units (ft, ft/s, mph) |
| Head-up display | HU | Mirror image display |
| Head-down display | HD | Does not mirror image display |
| Low intensity | IL | Reduce display intensity |
| High intensity | IH | Set higher display intensity |
| BT enable | BL | Enable (green) or disable (red) Bluetooth |
| BT address | AD | Show Bluetooth address (name) |
| BT password | PS | Show Bluetooth password |
| Firmware version | FW | Show Firmware version |
Figure 1 Menu Tree
The pilot can start 3EYE in 4 possible modes:
AltiVar mode (AV) - measures atmospheric pressure, displays the selected view, and logs events.
Demo mode (DE) - simulates selected views for demonstration.
Configuration mode (CF) - configures 3EYE.
Delete mode (DL) - permanently deletes all logs and resets the configuration to factory settings.
In this mode, 3EYE measures atmospheric pressure, shows the selected view, and logs events.
⚠️WARNING Start 3EYE ONLY ON GROUND LEVEL. You cannot start 3EYE during vertical activity.
The pilot can switch between different views at any time in this mode. See the "Pilot Views" section for more details.
The status LED will blink green once every 2 seconds.
3EYE simulates the following scenarios:
Skydive altimeter (AL) demo: Rapid ascent to 4300m (display dims to low intensity), followed by free fall to the ground (display increases to maximum intensity).
Dynamic variometer (DY) demo: Jump from 1000m, gliding at 18-20m/s with small oscillations of ±2m/s.
Speed dive variometer (SP) demo: Jump from 4000m, reaching 540 km/h.
Standard variometer (V) demo: Vertical changes between -3m/s and +3m/s.
You can switch between different views in this mode.
The status LED will blink twice every 2 seconds.
⚠️WARNING This mode does not measure atmospheric pressure; the values are simulated.
NOTICE During freefall, the device automatically sets the display to maximum intensity until the vertical event is complete.
In this mode you can change only basing setting:
Unit - metric system (M) or imperial system (F)
Display type - head-up (HU) or standard display (SD)
Display intensity - low intensity (IL) or high intensity (IH)
Bluetooth enable/disable - BLE enabled (BL) or BLE disabled (BL)
All other setting you can change with mobile app Link3EYE .
Following settings are read only:
Show Bluetooth address (name) (AD)
Show Bluetooth password (PS)
Show Firmware version (FW)
This mode permanently deletes the entire log. After stepping into this mode, you must confirm by selecting delete (DL) one more time or exit (EX) if you do not want to proceed with the deletion.
3EYE has four views:
Skydive altimeter (AL)
Dynamic variometer (DY)
Speed dive variometer (SP)
Standard variometer (V)
To switch views, press the button briefly.
Displays altitude in meters (M) or feet (F). Even though the 3EYE sensor can measure altitude to less than 1 m, as display has only 2 digit, displayed value depends resolution type.
NOTICE When freefall is detected, display will bright with max intensity.
⚠️WARNING In Altimeter view, the ground level may not display a value of exactly 0 because 3EYE uses a highly sensitive sensor capable of detecting elevation differences as small as 1 meter, or even 1 foot.
⚠️WARNING If free fall is detected at 400 meters (default value) or lower, the display will flicker.
On the 3EYE HUD, only the unit system can be changed directly: meters (M) or feet (F).
All other altimeter settings are configured using the Link3EYE mobile app:
| Altitude [m] | Resolution [m] | Altitude [ft] | Resolution [ft] |
|---|---|---|---|
| 0 - 100 | 1 | 0 - 1000 | 10 |
| 100 - 1000 | 10 | 1000 - 10000 | 100 |
| > 1000 | 100 | > 10000 | 1000 |
Example:
| Altitude [m] | Display value |
|---|---|
| 42 | 42 [m] |
| 256 | .25 [1000*m] |
| 1969 | 1.9 [1000*m] |
| Altitude [ft] | Display value [1000*ft] |
|---|---|
| 256 | .25 |
| 1969 | 1.9 |
| 12500 | 12 |
Available only for metric system. Show all in [1000*m].
Example:
| Altitude [m] | Display value |
|---|---|
| 42 | 0.0 |
| 256 | 0.2 |
| 1969 | 1.9 |
LED colors change based on altitude and color limits can be changes with mobile app Link3EYE.
Default values:
| Altitude [m] | Altitude [ft] | Color |
|---|---|---|
| <0 | <0 | White |
| 0 - 100 | 0 - 330 | White |
| 100 - 800 | 330 - 2624 | Red |
| 800 - 1300 | 2624 - 4265 | Yellow |
| >1300 | >4265 | Green |
3EYE HUD wakes up when a vertical event is detected (e.g., when the airplane starts climbing). At 30 meters above the ground, 3EYE HUD will begin displaying the altitude with low intensity.
| Setting | Description |
|---|---|
| Red Warning Signal | The display blinks when freefall altitude drops below the Red Limit. |
| 3s Yellow Warning Signal | The display blinks for 3 seconds during the green-to-yellow altitude transition. |
Controls when the altimeter is continuously visible during the climb to altitude. Following options you can set with Link3EYE app.
| Option | Behavior |
|---|---|
| Off | Display is always off during the entire ascent. |
| Red Limit | Continuous display until ascending past the Red Limit altitude else shows altitude only briefly every 30 seconds during ascent. |
| Yellow Limit | Continuous display until ascending past the Yellow Limit altitude else shows altitude only briefly every 30 seconds during ascent. |
| Always On | Display is always on during the entire ascent. |
When enabled, the current altitude is displayed continuously and the display never enters sleep mode. As a result, power consumption is significantly increased.
With this option enabled, the 3EYE device displays altitude immediately when the control switch is activated.
When disabled, altitude is displayed only when the 3EYE device detects a significant change in atmospheric pressure caused by a change in altitude.
Shows the trend fall rate in m/s (M.S) or f/s (F.S), which is the difference between the reference and real fall rate.
If the trend fall rate is slower than the reference fall rate, it shows green. If faster, it shows red.
The reference fall rate is not fixed; it calculates continuously.
NOTICE 3EYE wakes up approximately 2 seconds after freefall begins and displays a yellow "0" until it calculates the first reference speed.
For example, if the reference vertical rate is 21 m/s and the current rate is 19 m/s, the display shows 2 m/s in green (circled by a dashed line on the diagram).
Figure 2 Vertical speed diagram in relative mode
For example, if the reference vertical rate is 21 m/s and the current rate is 19 m/s, the display shows 19 m/s in green (circled by a dashed line on the diagram). During a fall, the vertical rate is displayed as a negative value.
Figure 2 Vertical speed diagram in absolute mode
Shows vertical descent speed in km/h (KM)or mph (ML) with resolution 10 units, with different colors for speed ranges:
| Speed [km/h] | Speed [mph] | Color |
|---|---|---|
| 0 | 0 | White |
| 0 - 200 | 0 - 125 | Green |
| 200 - 400 | 125 - 250 | Yellow |
| >400 | 250 | Red |
NOTICE 3EYE wakes up about 2 seconds after free fall begins.
⚠️WARNING Below 1700 meters (default value) during free fall, the LEDs will flicker.
Shows vertical speed in m/s (M.S) or f/s (F.S). Green LEDs show rising altitude, and red LEDs show descending altitude.
3EYE wakes up as soon as this view is selected and remains active continuously.
3EYE resets ground level: 1. when it is turned on (Pressure must remain stable for at least 5 seconds) or 2. when user do reset to ground level with Link3EYE mobile app.
⚠️WARNING In Altimeter view, the ground level may not display a value of exactly 0 because 3EYE uses a highly sensitive sensor capable of detecting elevation differences as small as 1 m, or even 1 ft.
3EYE automatically logs vertical events from the exit point to ground level.
The 3EYE saves a vertical event samples to memory when the device detects stable ground conditions.
A sample is saved only if:
Logs can be downloaded via mobile app Link3EYE .
3EYE has a 830mAh rechargeable battery. It takes about 16 hours to fully charge. The display shows the battery level as a percentage.
⚠️WARNING When charging the battery for the first time, it is strongly recommended that you wait until the battery is fully charged.
| Battery level [%] | Color | Description |
|---|---|---|
| <10% | Red | Device will stop unless in a vertical event. |
| <20% | Orange | |
| 20% | Yellow | Minimum battery level to start 3EYE |
| <30% | Yellow | Low level warning |
| 30 - 97% | Blue | |
| >=97% | Cyan | Fully charged |
⚠️WARNING If the battery level drops below 10%, 3EYE will shut down unless a vertical event is in progress.
⚠️WARNING If the battery level drops below 20%, 3EYE cannot be started. To start 3EYE, the battery level must be at least 20%.
NOTICE The battery level shown during charging is approximate and may differ from the actual battery level observed during discharging.
The following values reflect average working times under typical conditions with factory settings, while actual performance varying based on pilot habits and environmental factors.
| State | Time to Discharge |
|---|---|
| Turned off | 1 year min |
| Altimeter | 40 jumps |
| Wingsuit variometer | 60 jumps |
| Speed dive variometer | 60 jumps |
| Standard variometer | 5 hours |
The yellow status LED is located in the top-left corner of the display.
The LED blinking pattern indicates the health/status of the 3EYE device.
| Blinking pattern | Status |
|---|---|
| Continues | Low battery detected |
| 10Hz | On exit, unable to enter sleep mode |
| 5Hz | During normal operation, temperature > 50˙C |
| 2Hz | Flash memory error |
| Ones each 2s | Normal operation, AltVar mode |
| Twice each 2s | Normal operation, Demo mode |
| Three times each 2s | Normal operation, Config mode |
During startup and operation, the 3EYE performs a self-check. If it detects an error or warning, it shows the corresponding code on the display.
| LED Color | Code | Meaning |
|---|---|---|
| Red | Er | Barometer sensor malfunction |
| Yellow | W1 | Flash memory failed to power up |
| Yellow | W2 | Unable to read configuration from flash |
| Yellow | W3 | Device programmed in real test mode |
If an error is detected, the 3EYE shuts down.
If a warning is detected, the 3EYE continues operating with default settings.
The 3EYE device supports a wide range of configurable parameters that can be adjusted through a mobile app Link3EYE .
| Parameter | Range | Default |
|---|---|---|
| Unit System | Metric, Imperial | Metric |
| Display Type | Head-up, head-down | Head-up |
| Font Type | Efficient, Standard | Efficient |
| Min Display Intensity | 2, 220 | 40 |
| Max Display Intensity | 2, 220 | 160 |
| Night Mode | Off, On | Off |
| Bluetooth Enable | Yes, No | Yes |
| Altimeter Resolution | Floating point, Fix point | Floating point |
| Altimeter White Limit | 0, 100 m | 100 m |
| Altimeter Red Limit | 0, 2000 m | 800 m |
| Altimeter Yellow Limit | 0, 2000 m | 1300 m |
| Red Warning Signal | Off, On | On |
| 3s Yellow Warning Signal | Off, On | On |
| Ascent Visibility | Off, Red Limit, Yellow Limit, On | Red Limit |
| Dynamic Vario Display mode | Relative, Absolute | Relative |
| Speed Vario Blinking Enable | Yes, No | Yes |
| Speed Vario Blinking Altitude | 0, 4000 m | 1700 m |
| Standard Vario Resolution | Round values, Floating Point | Round values |
Homepage: https://3eye.blue